sourCEntral - mobile manpages

pdf

geninfo

NAME

geninfo − Generate tracefiles from .da files

SYNOPSIS

geninfo [−h|−−help] [−v|−−version] [−q|−−quiet]

[−i|−−initial] [−t|−−test−name test−name]
[−o|−−output−filename filename] [−f|−−follow]
[−b|−−base−directory directory]
[−−checksum] [−−no−checksum]
[−−compat−libtool] [−−no−compat−libtool]
[−−gcov−tool tool] [−−ignore−errors errors]
directory

DESCRIPTION

geninfo converts all GCOV coverage data files found in directory into tracefiles, which the genhtml tool can convert to HTML output.

Unless the −−output−filename option is specified, geninfo writes its output to one file per .da file, the name of which is generated by simply appending ".info" to the respective .da file name.

Note that the current user needs write access to both directory as well as to the original source code location. This is necessary because some temporary files have to be created there during the conversion process.

Note also that geninfo is called from within lcov, so that there is usually no need to call it directly.

OPTIONS

−b directory
−−base−directory
directory

Use directory as base directory for relative paths.

Use this option to specify the base directory of a build−environment when geninfo produces error messages like:

ERROR: could not read source file /home/user/project/subdir1/subdir2/subdir1/subdir2/file.c

In this example, use /home/user/project as base directory.

This option is required when using geninfo on projects built with libtool or similar build environments that work with a base directory, i.e. environments, where the current working directory when invoking the compiler is not the same directory in which the source code file is located.

Note that this option will not work in environments where multiple base directories are used. In that case repeat the geninfo call for each base directory while using the −−ignore−errors option to prevent geninfo from exiting when the first source code file could not be found. This way you can get partial coverage information for each base directory which can then be combined using the −a option.

−−checksum
−−no−checksum

Specify whether to generate checksum data when writing tracefiles.

Use −−checksum to enable checksum generation or −−no−checksum to disable it. Checksum generation is disabled by default.

When checksum generation is enabled, a checksum will be generated for each source code line and stored along with the coverage data. This checksum will be used to prevent attempts to combine coverage data from different source code versions.

If you don’t work with different source code versions, disable this option to speed up coverage data processing and to reduce the size of tracefiles.

−−compat−libtool
−−no−compat−libtool

Specify whether to enable libtool compatibility mode.

Use −−compat−libtool to enable libtool compatibility mode or −−no−compat−libtool to disable it. The libtool compatibility mode is enabled by default.

When libtool compatibility mode is enabled, geninfo will assume that the source code relating to a .da file located in a directory named ".libs" can be found in its parent directory.

If you have directories named ".libs" in your build environment but don’t use libtool, disable this option to prevent problems when capturing coverage data.

−f
−−follow

Follow links when searching .da files.

−−gcov−tool tool

Specify the location of the gcov tool.

−h
−−help

Print a short help text, then exit.

−−ignore−errors errors

Specify a list of errors after which to continue processing.

Use this option to specify a list of one or more classes of errors after which geninfo should continue processing instead of aborting.

errors can be a comma−separated list of the following keywords:

gcov: the gcov tool returned with a non−zero return code.

source: the source code file for a data set could not be found.

−i
−−initial

Capture initial zero coverage data.

Run geninfo with this option on the directories containing .bb, .bbg or .gcno files before running any test case. The result is a "baseline" coverage data file that contains zero coverage for every instrumented line. Combine this data file (using lcov −a) with coverage data files captured after a test run to ensure that the percentage of total lines covered is correct even when not all source code files were loaded during the test.

−o output−filename
−−output−filename
output−filename

Write all data to output−filename.

If you want to have all data written to a single file (for easier handling), use this option to specify the respective filename. By default, one tracefile will be created for each processed .da file.

−q
−−quiet

Do not print progress messages.

Suppresses all informational progress output. When this switch is enabled, only error or warning messages are printed.

−t testname
−−test−name
testname

Use test case name testname for resulting data. Valid test case names can consist of letters, decimal digits and the underscore character (’_’).

This proves useful when data from several test cases is merged (i.e. by simply concatenating the respective tracefiles) in which case a test name can be used to differentiate between data from each test case.

−v
−−version

Print version number, then exit.

FILES

/etc/lcovrc

The system−wide configuration file.

~/.lcovrc

The per−user configuration file.

Following is a quick description of the tracefile format as used by genhtml, geninfo and lcov.

A tracefile is made up of several human−readable lines of text, divided into sections. If available, a tracefile begins with the testname which is stored in the following format:

TN:<test name>

For each source file referenced in the .da file, there is a section containing filename and coverage data:

SF:<absolute path to the source file>

Following is a list of line numbers for each function name found in the source file:

FN:<line number of function start>,<function name>

Then there is a list of execution counts for each instrumented line (i.e. a line which resulted in executable code):

DA:<line number>,<execution count>[,<checksum>]

Note that there may be an optional checksum present for each instrumented line. The current geninfo implementation uses an MD5 hash as checksumming algorithm.

At the end of a section, there is a summary about how many lines were found and how many were actually instrumented:

LH:<number of lines with a non−zero execution count>
LF:<number of instrumented lines>

Each sections ends with:

end_of_record

In addition to the main source code file there are sections for all #included files which also contain executable code.

Note that the absolute path of a source file is generated by interpreting the contents of the respective .bb file (see gcov (1) for more information on this file type). Relative filenames are prefixed with the directory in which the .bb file is found.

Note also that symbolic links to the .bb file will be resolved so that the actual file path is used instead of the path to a link. This approach is necessary for the mechanism to work with the /proc/gcov files.

AUTHOR

Peter Oberparleiter <Peter DOT Oberparleiter AT de DOT ibm DOT com>

SEE ALSO

lcov(1), genhtml(1), genpng(1), gendesc(1), gcov(1)

pdf