sourCEntral - mobile manpages

pdf

ED(4) BSD Kernel Interfaces Manual ED(4)

NAME

ed — NE-2000 and WD-80x3 Ethernet driver

SYNOPSIS

To compile this driver into the kernel, place the following lines in your kernel configuration file:

device miibus
device ed

Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

if_ed_load="YES"

DEPRECATION NOTICE

The ed driver is not present in FreeBSD 13.0 and later. See https://github.com/freebsd/fcp/blob/master/fcp-0101.md for more information.

DESCRIPTION

The ed driver provides support for 8 and 16bit Ethernet cards that are based on the National Semiconductor DS8390 and similar NICs manufactured by other companies. The ed driver also supports many PC Card chips which interface via MII to a PHY. Axiom’s AX88790, AX88190 and AX88190A; DLink’s DL10019 and DL10022; and Tamarack’s TC5299J chips all support internal or external MII/PHY combinations. Realtek’s PCI and ISA RTL80x9-based cards are also supported. For these chipsets, autonegotiation and status reporting are supported.

In addition to the standard port and IRQ specifications, the ed driver also supports a number of flags which can force 8/16bit mode, enable/disable multi-buffering, and select the default interface type (AUI/BNC, and for cards with twisted pair, AUI/10BaseT).

The flags are a bit field, and are summarized as follows:

0x01

Disable transceiver. On those cards which support it, this flag causes the transceiver to be disabled and the AUI connection to be used by default.

0x02

Force 8bit mode. This flag forces the card to 8bit mode regardless of how the card identifies itself. This may be needed for some clones which incorrectly identify themselves as 16bit, even though they only have an 8bit interface. This flag takes precedence over force 16bit mode.

0x04

Force 16bit mode. This flag forces the card to 16bit mode regardless of how the card identifies itself. This may be needed for some clones which incorrectly identify themselves as 8bit, even though they have a 16bit ISA interface.

0x08

Disable transmitter multi-buffering. This flag disables the use of multiple transmit buffers and may be necessary in rare cases where packets are sent out faster than a machine on the other end can handle (as evidenced by severe packet lossage). Some (non-FreeBSD :-)) machines have terrible Ethernet performance and simply cannot cope with 1100K+ data rates. Use of this flag also provides one more packet worth of receiver buffering, and on 8bit cards, this may help reduce receiver lossage.

When using a 3c503 card, the AUI connection may be selected by specifying the link2 option to ifconfig(8) (BNC is the default).

HARDWARE

The ed driver supports the following Ethernet NICs:

3Com 3c503 Etherlink II (options ED_3C503)

AR-P500 Ethernet

Accton EN1644 (old model), EN1646 (old model), EN2203 (old model) (110pin) (flags 0xd00000)

Accton EN2212/EN2216/UE2216

Allied Telesis CentreCOM LA100-PCM_V2

AmbiCom 10BaseT card (8002, 8002T, 8010 and 8610)

Bay Networks NETGEAR FA410TXC Fast Ethernet

Belkin F5D5020 PC Card Fast Ethernet

Billionton LM5LT-10B Ethernet/Modem PC Card

Billionton LNT-10TB, LNT-10TN Ethernet PC Card

Bromax iPort 10/100 Ethernet PC Card

Bromax iPort 10 Ethernet PC Card

Buffalo LPC2-CLT, LPC3-CLT, LPC3-CLX, LPC4-TX, LPC-CTX PC Card

Buffalo LPC-CF-CLT CF Card

CNet BC40 adapter

Compex Net-A adapter

Compex RL2000

Corega Ether PCC-T/EtherII PCC-T/FEther PCC-TXF/PCC-TXD PCC-T/Fether II TXD

Corega LAPCCTXD (TC5299J)

CyQ’ve ELA-010

DEC EtherWorks DE305

Danpex EN-6200P2

D-Link DE-660, DE-660+

D-Link IC-CARD/IC-CARD+ Ethernet

ELECOM Laneed LD-CDL/TX, LD-CDF, LD-CDS, LD-10/100CD, LD-CDWA (DP83902A)

Hawking PN652TX PC Card (AX88790)

HP PC Lan+ 27247B and 27252A (options ED_HPP)

IBM Creditcard Ethernet I/II

I-O DATA ET2/T-PCI

I-O DATA PCLATE

Kingston KNE-PC2, CIO10T, KNE-PCM/x Ethernet

KTI ET32P2 PCI

Linksys EC2T/PCMPC100/PCM100, PCMLM56

Linksys EtherFast 10/100 PC Card, Combo PCMCIA Ethernet Card (PCMPC100 V2)

MACNICA Ethernet ME1 for JEIDA

MELCO LGY-PCI-TR

MELCO LPC-T/LPC2-T/LPC2-CLT/LPC2-TX/LPC3-TX/LPC3-CLX

NDC Ethernet Instant-Link

National Semiconductor InfoMover NE4100

NetGear FA-410TX

NetVin NV5000SC

Network Everywhere Ethernet 10BaseT PC Card

New Media LANSurfer 10+56 Ethernet/Modem

New Media LANSurfer

Novell NE1000/NE2000/NE2100

PLANEX ENW-8300-T

PLANEX FNW-3600-T

Psion 10/100 LANGLOBAL Combine iT

RealTek 8019

RealTek 8029

Relia Combo-L/M-56k PC Card

SMC Elite 16 WD8013

SMC Elite Ultra

SMC WD8003E/WD8003EBT/WD8003S/WD8003SBT/WD8003W/WD8013EBT/WD8013W and clones

SMC EZCard PC Card, 8040-TX, 8041-TX (AX88x90), 8041-TX V.2 (TC5299J)

Socket LP-E, ES-1000 Ethernet/Serial, LP-E CF, LP-FE CF

Surecom EtherPerfect EP-427

Surecom NE-34

TDK 3000/3400/5670 Fast Ethernet/Modem

TDK LAK-CD031, Grey Cell GCS2000 Ethernet Card

TDK DFL5610WS Ethernet/Modem PC Card

Telecom Device SuperSocket RE450T

Toshiba LANCT00A PC Card

VIA VT86C926

Winbond W89C940

Winbond W89C940F

ISA, PCI and PC Card devices are supported.

The ed driver does not support the following Ethernet NICs:

Mitsubishi LAN Adapter B8895

DIAGNOSTICS

ed%d: failed to clear shared memory at %x - check configuration.  When the card was probed at system boot time, the ed driver found that it could not clear the card’s shared memory. This is most commonly caused by a BIOS extension ROM being configured in the same address space as the Ethernet card’s shared memory. Either find the offending card and change its BIOS ROM to be at an address that does not conflict, or change the settings in device.hints(5) that the card’s shared memory is mapped at a non-conflicting address.

ed%d: Invalid irq configuration (%d) must be 2-5 for 3c503.  The IRQ number that was specified in the device.hints(5) file is not valid for the 3Com 3c503 card. The 3c503 can only be assigned to IRQs 2 through 5.

ed%d: Cannot find start of RAM. 
ed%d: Cannot find any RAM, start : %d, x = %d. 
The probe of a Gateway card was unsuccessful in configuring the card’s packet memory. This likely indicates that the card was improperly recognized as a Gateway or that the card is defective.

ed: packets buffered, but transmitter idle.  Indicates a logic problem in the driver. Should never happen.

ed%d: device timeout  Indicates that an expected transmitter interrupt did not occur. Usually caused by an interrupt conflict with another card on the ISA bus. This condition could also be caused if the kernel is configured for a different IRQ channel than the one the card is actually using. If that is the case, you will have to either reconfigure the card using a DOS utility or set the jumpers on the card appropriately.

ed%d: NIC memory corrupt - invalid packet length %d.  Indicates that a packet was received with a packet length that was either larger than the maximum size or smaller than the minimum size allowed by the IEEE 802.3 standard. Usually caused by a conflict with another card on the ISA bus, but in some cases may also indicate faulty cabling.

ed%d: remote transmit DMA failed to complete.  This indicates that a programmed I/O transfer to an NE1000 or NE2000 style card has failed to properly complete. Usually caused by the ISA bus speed being set too fast.

ed%d: Invalid irq configuration (%ld) must be %s for %s  Indicates the device has a different IRQ than supported or expected.

ed%d: Cannot locate my ports!  The device is using a different I/O port than the driver knows about.

ed%d: Cannot extract MAC address  Attempts to get the MAC address failed.

ed%d: Missing mii!  Probing for an MII bus has failed. This indicates a coding error in the PC Card attachment, because a PHY is required for the chips that generate this error message.

SEE ALSO

altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), device.hints(5), ifconfig(8)

HISTORY

The ed device driver first appeared in FreeBSD 1.0.

AUTHORS

The ed device driver and this manual page were written by David Greenman.

CAVEATS

Early revision DS8390 chips have problems. They lock up whenever the receive ring-buffer overflows. They occasionally switch the byte order of the length field in the packet ring header (several different causes of this related to an off-by-one byte alignment) - resulting in "NIC memory corrupt - invalid packet length" messages. The card is reset whenever these problems occur, but otherwise there is no problem with recovering from these conditions.

The NIC memory access to 3Com and Novell cards is much slower than it is on WD/SMC cards; it is less than 1MB/second on 8bit boards and less than 2MB/second on the 16bit cards. This can lead to ring-buffer overruns resulting in dropped packets during heavy network traffic.

The Mitsubishi B8895 PC Card uses a DP83902, but its ASIC part is undocumented. Neither the NE2000 nor the WD83x0 drivers work with this card.

BUGS

The ed driver is a bit too aggressive about resetting the card whenever any bad packets are received. As a result, it may throw out some good packets which have been received but not yet transferred from the card to main memory.

The ed driver is slow by today’s standards.

PC Card attachment supports the D-Link DMF650TX LAN/Modem card’s Ethernet port only at this time.

Some devices supported by ed do not generate the link state change events used by devd(8) to start dhclient(8). If you have problems with dhclient(8) not starting and the device is always attached to the network it may be possible to work around this by changing “DHCP” to “SYNCDHCP” in the ifconfig_ed0 entry in /etc/rc.conf.

BSD October 24, 2018 BSD

pdf