sourCEntral - mobile manpages

pdf

ACPI_PANASONIC(4) BSD Kernel Interfaces Manual ACPI_PANASONIC(4)

NAME

acpi_panasonic — ACPI hotkey driver for Panasonic laptops

SYNOPSIS

To compile this driver into the kernel, place the following line in your kernel configuration file:

device acpi_panasonic

Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

acpi_panasonic_load="YES"

DESCRIPTION

The acpi_panasonic driver enables such hotkey facilities of various Panasonic laptops as changing LCD brightness, controlling mixer volumes, entering sleep or suspended state and so on. On the following models it is reported to work: Let’s note (or Toughbook, outside Japan) CF-R1N, CF-R2A and CF-R3. It may also work on other models as well.

The driver consists of three functionalities. The first is to detect hotkey events and take corresponding actions, which include changing LCD luminance and speaker mute state. The second role is to notify occurrences of the event by way of devctl(4) and eventually to devd(8). The third and last is to provide a way to adjust LCD brightness and sound mute state via sysctl(8).

Hotkeys
There are 9 hotkeys available on the supported hardware:

Fn+F1

Make LCD backlight darker.

Fn+F2

Make LCD backlight brighter.

Fn+F3

Switch video output between LCD and CRT. Not supported by the acpi_panasonic driver.

Fn+F4

Toggle muting the speaker.

Fn+F5

Turn the mixer volume down.

Fn+F6

Turn the mixer volume up.

Fn+F7

Enter suspend-to-RAM state.

Fn+F9

Show battery status.

Fn+F10

Enter suspend-to-disk state.

Actions are automatically taken within the driver for Fn+F1, Fn+F2 and Fn+F4. For the other events such as mixer control and showing battery status, devd(8) should take the role as described below.

devd(8) Events
When notified to devd(8), the hotkey event provides the following information:

system

"ACPI"

subsystem

"Panasonic"

type

The source of the event in ACPI namespace. The value depends on the model but typically "\_SB_.HKEY".

notify

Event code (see below).

Event codes to be generated are assigned as follows:

0x81-0x86, 0x89

Fn+F<n> pressed. 0x81 corresponds to Fn+F1, 0x82 corresponds to Fn+F2, and so on.

0x01-0x07, 0x09, 0x1a

Fn+F<n> released. 0x01 corresponds to Fn+F1, 0x02 corresponds to Fn+F2, and so on.

SYSCTL VARIABLES

The following MIBs are available:

hw.acpi.panasonic.lcd_brightness_max

The maximum level of brightness. This read-only value is automatically set according to hardware model.

hw.acpi.panasonic.lcd_brightness_min

The minimum level of brightness. This read-only value is automatically set according to hardware model.

hw.acpi.panasonic.lcd_brightness

Current brightness level of the LCD (read-write). The value ranges from hw.acpi.panasonic.lcd_brightness_min to hw.acpi.panasonic.lcd_brightness_max.

hw.acpi.panasonic.sound_mute

A read-write boolean flag to control whether to mute the speaker. The value 1 means to mute and 0 not.

SEE ALSO

acpi(4), devd.conf(5), devd(8), sysctl(8)

HISTORY

The acpi_panasonic driver first appeared in FreeBSD 5.3.

AUTHORS

The acpi_panasonic driver and this manual page were written by OGAWA Takaya 〈t-ogawa AT triaez DOT kaisei DOT org〉 and TAKAHASHI Yoshihiro 〈nyan AT FreeBSD DOT org〉.

BSD June 19, 2015 BSD

pdf