ledctl − Intel(R) LED control application for a storage enclosures.
ledctl [ OPTIONS ] pattern_name=list_of_devices ...
The ledctl is an user space application designed to control LEDs associated with each slot in an enclosure or a drive bay. The LEDs of devices listed in list_of_devices are set to the given pattern pattern_name and all other LEDs are turned off. User must have root privileges to use this application.
There are two types of systems: 2−LEDs systems (Activity LED, Status LED ) and 3−LEDs systems (Activity LED, Locate LED, Fail LED ). The ledctl application uses SGPIO and SES−2 protocol to control LEDs. The program implements IBPI patterns of SFF−8489 specification for SGPIO. Please note some enclosures do not stick close to SFF−8489 specification. It might happen that enclosure’s processor will accept an IBPI pattern but it will blink the LEDs at variance with SFF−8489 specification or it has limited number of patterns supported.
LED management ( AHCI ) and SAF-TE protocols are not supported.
The ledctl application has been verified to work with Intel(R) storage controllers (i.e. Intel(R) AHCI controller and Intel(R) SAS controller). The application might work with storage controllers of other vendors (especially SCSI/SAS controllers). However, storage controllers of other vendors have not been tested.
The ledmon application has the highest priority when accessing LEDs. It means that some patterns set by ledctl may have no effect if ledmon is running (except Locate pattern).
The ledctl application is a part of Intel(R) Enclosure LED Utilities.
Pattern Names
The ledctl application accepts the following names for pattern_name argument according to SFF−8489 specification.
locate |
Turns Locate LED associated with the given device(s) or empty slot(s) on. |
locate_off
Turns only Locate LED off.
normal |
Turns Status LED, Failure LED and Locate LED off. |
|||
off |
Turns only Status LED and Failure LED off. |
ica or degraded
Visualizes "In a Critical Array" pattern.
rebuild or rebuild_p
Visualizes "Rebuild" pattern.
ifa or failed_array
Visualizes "In a Failed Array" pattern.
hotspare
Visualizes "Hotspare" pattern.
pfa |
Visualizes "Predicted Failure Analysis" pattern. |
failure or disk_failed
Visualizes "Failure" pattern.
ses_abort
SES−2 R/R ABORD
ses_rebuild
SES−2 REBUILD/REMAP
ses_ifa |
SES−2 IN FAILED ARRAY |
|||
ses_ica |
SES−2 IN CRIT ARRAY |
ses_cons_check
SES−2 CONS CHECK
ses_hotspare
SES−2 HOT SPARE
ses_rsvd_dev
SES−2 RSVD DEVICE
ses_ok |
SES−2 OK |
ses_ident
SES−2 IDENT
ses_rm |
SES−2 REMOVE |
ses_insert
SES−2 INSERT
ses_missing
SES−2 MISSING
ses_dnr |
SES−2 DO NOT REMOVE |
ses_active
SES−2 ACTIVE
ses_enbale_bb
SES−2 ENABLE BYP B
ses_enable_ba
SES−2 ENABLE BYP A
ses_devoff
SES−2 DEVICE OFF
ses_fault
SES−2 FAULT
Patterns Translation
When non SES−2 pattern is send to device in enclosure automatic translation is being done.
locate |
locate is translated to ses_ident |
locate_off
locate_off is translated to ~ses_ident
normal |
normal is translated to ses_ok |
|||
off |
off is translated to ses_ok |
degraded
degraded is translated to ses_ica
rebuild |
rebuild is translated to ses_rebuild |
rebuild_p
rebuild_p is translated to ses_rebuild
failed |
failed is translated to ses_ifa |
hotspare
hotspare is translated to ses_hotspare
pfa |
pfa is translated to ses_rsvd_dev |
|||
failure |
failure is translated to ses_fault |
disk_failed
disk_failed is translated to ses_fault
List of Devices
The application accepts a list of devices in two formats. The first format is a list with comma separated elements. The second format is a list in curly braces and elements are separated by space. See examples section bellow for details.
A device is a path to file in /dev directory or in /sys/block directory. It may identify a block device, a RAID device or a container device. In case of a RAID device or a container device a state will be set for all block devices associated, respectively.
The LEDs of devices listed in list_of_devices are set to the given pattern pattern_name and all other LEDs are turned off.
−c or −−config=path
Sets a path to local configuration file. If this option is specified the global configuration file and user configuration file has no effect.
−l or −−log=path
Sets a path to local log file. If this option is specified the global log file /var/log/ledctl.log is not used.
−h or −−help
Prints this text out and exits.
−v or −−version
Displays version of ledctl and information about the license and exits.
/var/log/ledctl.log
Global log file, used by all instances of ledctl application. To force logging to user defined file use −l option switch.
~/.ledctl
User configuration file, shared between ledmon and all ledctl application instances.
/etc/ledcfg.conf
Global configuration file, shared between ledmon and all ledctl application instances.
The following example illustrates how to locate a single block device.
ledctl locate=/dev/sda
The following example illustrates how to turn Locate LED off for the same block device.
ledctl locate_off=/dev/sda
The following example illustrates how to locate disks of a RAID device and how to set rebuild pattern for two block devices at the same time. This example uses both formats of device list.
ledctl locate=/dev/md127 rebuild={ /sys/block/sd[a−b] }
The following example illustrates how to turn Status LED and Failure LED off for the given device(s).
ledctl off={ /dev/sda /dev/sdb }
The following example illustrates how to locate a three block devices. This example uses the first format of device list.
ledctl locate=/dev/sda,/dev/sdb,/dev/sdc
Copyright (c) 2009−2013 Intel Corporation.
This program is distributed under the terms of the GNU General Public License as published by the Free Software Foundation. See the built-in help for details on the License and the lack of warranty.
This manual page was written by Artur Wojcik <artur DOT wojcik AT intel DOT com>. It may be used by others.